Question about kawasaki 2005 Mule 3010 4x4

Open Question

2002 2510 kawasaki mule engine will not turn over new batt tried to jump the relay very weak spark

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mule 550, It starts fine, but will not shut off when the key is turned off....any suggestions?


Hey Matt, sounds like the switch is going bad.. I would see if it will start - WITH THE KEY OFF by "jumping" the solenoid.. if the switch is bad.. it might start... and confirm the switch is bad..

Jun 21, 2017 | kawasaki 2008 Mule 3010 4x4

1 Answer

Mule 3010 has no power. in low or high it goes maybe 9 mph, has new pump, spark plugs, checked the vents, nothing is helping


What is the compression? This leads me to think you may have more of an internal issue.

Have the compression checked, with throttle wide open, then repost with the results.

May 20, 2017 | kawasaki 2005 Mule 3010 4x4

1 Answer

There is no fire to the spark plugs but will turn over what to check


First replace the spark plug with a new one. Then check the wires from the positive terminal on the battery to the coil and then to plugs. Put a 12 volt tester on the positive wires and the battery ground or any metal on the engine to see if circuit is hot. Hope this helps. Make sure you test the plug wire as well.

Sep 21, 2015 | kawasaki 2009 Mule 4010 Trans4x4

1 Answer

Mule kawasaki 3000 will jump start, but when I remove cables it dies


With the limited information given, I suspect you're going to need to have someone check your alternator.

Oct 06, 2014 | kawasaki 2008 Mule 3000

1 Answer

Kawasaki problems


it can be a few things it can be a bad solonid, bad connection, bad battery, or your starter needs new brushes

Jul 23, 2014 | kawasaki 2010 Mule 600

1 Answer

2012 kawasaki mule 4010 hitting on front cylinder only


First is the engine Diesel or Gas?
if it is a diesel engine it has almost got to be a compression or fuel problem if it is a Gas engine it can be a valve adjustment, fuel, compression, or spark problem

May 16, 2014 | kawasaki 2012 Mule 4010 4x4

1 Answer

Kawasaki mule 3010 won't do right and left signals when i press them, how to switch fuse for them?


Identify the fuse responsable for turn signals, extract it and insert another one with the same value in it's place.
Also could be turn's signals relay fault.

Oct 20, 2013 | kawasaki 2008 Mule 3010 4x4 Diesel

1 Answer

Kawasaki Mule 1999 Model


Hello Anon..
First, I would check to make sure the carbs are getting fuel, and then fuel getting into the cylinders. Your question about low oil - did you let it get low and then it quit? ...
If you put oil into the cylinders and only got 100psi, this might be your problem. You should be pumping around 120+psi without putting anything into the cylinders... Recheck the compression.= .take out all spark plugs...screw the gauge in until the o-ring seats, hold the throttle wide open while spinning the engine over for about 5 seconds... you should get 120psi +/- 10psi.
If you are getting less than 100psi.. it might be time for a rebuild..

May 24, 2017 | kawasaki 2005 Mule 3010 Trans 4x4

Not finding what you are looking for?
kawasaki 2005 Mule 3010 4x4 Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki ATVs Experts

yadayada
yadayada

Level 3 Expert

80417 Answers

Lawrence Oravetz

Level 3 Expert

10291 Answers

Glenn Smart
Glenn Smart

Level 3 Expert

818 Answers

Are you a kawasaki ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...