Question about kawasaki 2005 Mule 3010 4x4

Open Question

Clicking sound when trying to start Kawasaki mule 550. new battery and selanoid

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 10 Answers

SOURCE: battery life

the part is called a stattor or statter but it should be a black box with raised lovers on it attached to out side of bike usually in the front with 2 or 3 wires coming from it to a plug then the wires going into the engine.Check the plug for fit and cleaness or Change that box if that doesn't work it's internal. take it to a dealer or independent and have repaired

Posted on Jan 31, 2009

Ad
  • 25 Answers

SOURCE: Kawasaki Mule 3010, keeps getting flat battery, wont jump start

Sometimes when the battery keeps going dead like that, a component may be creating a current draw. you can do a simple current draw test with a fluke meter by setting the meter to read amps, make sure the test leads are in the proper portals on the fluke for an amp test, and disconnect one of the battery cables and connect the test leads in-line with the battery and cable. It would help to know you have a good fuse inside the fluke. They are easy to blow, and whatever you do, DO NOT try to start the unit with the meter hooked up for the amp draw test. That is how fuses are blown. With the key off, check for any amp draw. If there is, you can start unplugging components until the draw goes away. If there was no draw to begin with, you may have a stator coil (or alternantor, whichever it has) that is weak and can't keep up.

Posted on Jun 11, 2009

wayneman01
  • 301 Answers

SOURCE: Kawasaki Mule 500 KAF 300 starter will not work below 60 degrees.

Using a lighter viscosity engine oil can make all the difference. Try something on the order of a 5W-30 for ambient temperatures of 60F or below. Of course, it could also be that your starter solenoid is in the early stages of failure. You can easily check it by using a large screwdriver to bridge the two large cable connections on the top of the solenoid. If the starter spins when you do this, then the solenoid is bad.

Posted on Dec 07, 2009

  • 21 Answers

SOURCE: my 2008 kawasaki 3510 gas mule will not start. I

mabe firing problem

Posted on Mar 18, 2010

  • 2 Answers

SOURCE: 1999 kawasaki mule will not

the problem might be a cdi box or stater or might be a rectifire/regulator

Posted on Jun 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mule 550, It starts fine, but will not shut off when the key is turned off....any suggestions?


Hey Matt, sounds like the switch is going bad.. I would see if it will start - WITH THE KEY OFF by "jumping" the solenoid.. if the switch is bad.. it might start... and confirm the switch is bad..

Jun 21, 2017 | kawasaki 2008 Mule 3010 4x4

1 Answer

I have a 2003 kawasaki mule model 3000 it wont say running at idle what to do


Full tune up and carb clean .get new plug,air filter.oil Chang ,carb clean and adjustment.that should do it.,., try fuel filters and test fuel pump see if it's functioning properly.,.

Dec 10, 2016 | kawasaki 2005 Mule 3010 4x4

1 Answer

Where is the neutral safety switch for a kawaski 3010 mule


Kawasaki Mule Update - YouTube

? 2:16
www.youtube.com/watch?v=Fw_jeQUU6Hw
Jan 25, 2013 - Uploaded by Penguinboy1995
solenoid is reading battery voltage and the constant hot, it is not sending the 12 volts from the switch to the ...

Sep 19, 2015 | kawasaki 2005 Mule 3010 Trans 4x4

1 Answer

I have a Kawasaki 550 mule that won't hold a charge


Have you disconnected the battery and tried charging it to see if it would hold a charge disconnected? If not, the battery is probably bad. If it will hold a charge, then connect the battery ground cable, then touch the positive cable to the positive battery post and watch for a spark (make sure the key is turned off). If there's a spark, then something is pulling your batter down when the bike isn't running. Now if you have an electronic speedometer, dash gauges, etc., those will draw in order to maintain memory. Disconnect the wires to them then try again.
There's only so much I can tell you this way. I work on electrical systems often, and it can be a real process.

Nov 25, 2014 | ATVs

1 Answer

Replace drive belt 550 mule kawasaki


You will need a special tool from Kawasaki for the clutch tool removal to remove the belt and to install the new belt. Stop by your local dealer for the tool and they can explain the pretty simple way to remove the side panel and use of the tool. the tool runs about 76.00 Hope this helps you out some.

Sep 01, 2014 | ATVs

1 Answer

Kawasaki problems


it can be a few things it can be a bad solonid, bad connection, bad battery, or your starter needs new brushes

Jul 23, 2014 | kawasaki 2010 Mule 600

1 Answer

Kawasaki mule 3010


Check the starter or solenoid.

Apr 27, 2013 | kawasaki 2008 Mule 3010 Trans 4x4

Not finding what you are looking for?
kawasaki 2005 Mule 3010 4x4 Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki ATVs Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

Lawrence Oravetz

Level 3 Expert

10291 Answers

Glenn Smart
Glenn Smart

Level 3 Expert

818 Answers

Are you a kawasaki ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...