Question about Polaris 2007 Outlaw 90

Open Question

2007 polaris 90 outlaw wiring diagram

What voltage goes to CID box

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1140 Answers

SOURCE: Why is the flywheel making a grinding noise when trying to start my polaris outlaw 500?

The starter drive on the starter motor is defective. The teeth on the flywheel could be chewed up too. If you just installed a new starter, you may have to add or subtract clearance spacer metal tabs so that the starter drive engages properly with the flywheel.

Posted on Jun 05, 2014

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you bypass kill switch on a 2013 Polaris outlaw 50cc?


a kill switch either "makes" a circuit or "breaks" a circuit.., so - you can do one or the other... connect the two wires or disconnect the two wires...

Aug 10, 2017 | ATVs

1 Answer

Polris sport mans 800 x2 twin


I suspect one goes to the battery and the other is an aux power plug hookup. just guessing though.

Apr 18, 2017 | Polaris 2004 Sportsman 700 Twin

1 Answer

I have a 2007 Polaris 450 sportsman and my brother tried to jump it off with a 36 volt golf cart and fried the Ecm. what else could be fried. Headlights won't come on and it won't try to start at all


most likely
3 times the allowable voltage does tend to burn everything including starter motors , solenoids relays , light bulbs , ECM

Oct 25, 2016 | ATVs

1 Answer

A 2007 rancher 420 my fi light gives 9 blinks. Do you know what code this is and what it means


Most likely you water in one of the connectors, this code is for voltage high or voltage is low at the IAT sensor (air temp sensor in the air box) It could be the sensor connector that is at fault or the control unit back by the battery.

Sep 29, 2016 | ATVs

1 Answer

08 outlaw 90 no start clean carb run great 2 weeks cuts off few times start back then no start air cleaner bad clean crab no start plug drippin wet run 4 few gas hafe off


if the plug/s are wet , that is flooding and that is excessive fuel or float level , probably from a problem in the needle and seat area where the fuel supply is not being controlled
remove the needle and seat and clean all dirt and rubbish from the needle ans seat area
could come from rust and dirt in the tank so consider an inline fuel filter before the carby/s

Mar 05, 2016 | Polaris ATV

1 Answer

My front brake pads are only about the thickness of a dime. How thick should they be when new pads.m


You need to change them They are down about a 1/4 of the size they should be (4 dimes)

Jan 18, 2016 | Polaris 2008 Outlaw 90

1 Answer

The is no power to the ignition dash lights head lights, winch but will pull start


First check the positive cable at battery and at the starter relay that the positive wire usually goes to. Somewhere right around there should be a fuse - that fuse goes out and your ignition system is kaput - pull start or nothing. If nothing at all happens - more than likely your fuse or what...yamaha had them on a lot of the 90s - 00s bikes - it was called a starter cut-off relay - it was a small black box wired in right by the postive cable where it goes to starter relay. Also check your ground cable at battery and where it goes to engine, usually. if all that checks out - let me know your year, make & model and if I have the tech info I can tell you where to start and how to troubleshoot - all the best

Dec 27, 2015 | ATVs

2 Answers

2014 polaris outlaw 50, new battery and starter relay. Relay still just clicks. Also have no power to the starter. Any ideas?


check all fuses,then check power at the switch,then make sure the solenoid is connected properly,does it have a shut off if the rider falls off?

May 28, 2015 | Polaris 2014 Outlaw 50

1 Answer

So I'm wiring up the KFI stealth 3500 winch on my ATV do I need to ground the contactor box to my frame


If it has a black wire that goes to neg on the battery.Pos or red to a switch if the winch does not have one.

Mar 24, 2015 | ATVs

Not finding what you are looking for?
Polaris 2007 Outlaw 90 Logo

Related Topics:

306 people viewed this question

Ask a Question

Usually answered in minutes!

Top Polaris ATVs Experts

john h

Level 3 Expert

12744 Answers

Matt Olenzek
Matt Olenzek

Level 2 Expert

297 Answers

Wade Mobley
Wade Mobley

Level 3 Expert

489 Answers

Are you a Polaris ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...